Olympus-OM
[Top] [All Lists]

Re: [OM] DeFanged + Rewind Crank - Another Problem to fix ?

Subject: Re: [OM] DeFanged + Rewind Crank - Another Problem to fix ?
From: clintonr@xxxxxxxxxxxxxxxx
Date: Thu, 21 Jun 2001 23:20:23 -0500
Great description!  A couple of other suggestions:

Grip the flat sides of the end of the rewind shaft from the outside with
needlenose pliars, down where the fork is.  In other words, turn the
shaft so you can see between the legs of the fork -- now turn it 90
degrees -- see how the legs of the fork are flat when viewed from the
side?  Put your pliars on the _flats_ of the fork.  DON'T put anything
_between_ the legs of the fork -- if you spread the fork, it will stick
in the collar when you pull it up to open the back.

Next, if you don't want to bother with a paperclip (which I've done 1000
times!), you can also try just putting a slight bend in the pin that's
there.  Remove the knob and spring, slide the lever into the knob so you
can get to the pin, slide the pin half-way out of it's hole and give it
a little bend with your pliars.  Now press the pin back into the lever
-- the bend will keep it centered!

Incidentally, the plate that goes under the rewind knob should be
oriented so that the "spring"-part preses _up_, against the rewind
lever, and the squared-off plate is _down_.

Bill Stanke wrote:
> 
> Dave:
> 
> I fixed this on my OM-1.  I believe that the OM-2SP should be the same.
> First, remove the rewind knob from the camera. (Instructions from the OM
> Repair FAQ:)
> 
> 1. Remove the rewind knob:
> 
>         This was actually a little tricky, as I did not know how it was
>         supposed to come off.  The book just said unscrew it.   It
>         took a little time but I finally worked out that the whole knob
>         just unscrews from the shaft, exactly what the book said....
>         You need some sort of implement to stop the shaft turning while
>         you unscrew it.  Don't use pliers as the rewind forks bend
>         very easily.  I ended up cutting a chop stick to fit as close
>         as possible to the shaft, and avoided placing much pressure on
>         the forks.  There is a small screw in the center of the rewind
>         knob.  John H mentioned that this should not be touched.
> 
> 2.  Once you the rewind knob off, look at the underside of the knob.
> You will need to remove a spacer/washer.  The rewind lever is held in
> place by a small length of wire.  You should be able to cut a length
> from an ordinary #1 paper clip (honest!) and thread it through the
> rewind lever.  Use a small screwdriver to carefully push the wire into
> the groove in the body of the rewind knob.  The rewind lever pivots on
> wire, there isn't really a hinge.
> 
> 3. Replace the spacer/washer, and re-assemble the rewind knob on the
> shaft.
> 
> 4.  Again, this was the repair for an OM-1.  I assume that the OM-2SP
> has a similar arrangement. Your mileage may vary, etc.
> 
> Good luck!
> 
> Bill Stanke
> 
> > I also have a (smaller) rewind crank problem on this OM-2SP - the
> > little hinge on the rewind crank handle is broken on one side, and the
> > handle is therefore a little bit loose (but will rewind OK - I will have to
> > do it carefully!).
> >
> > What holds that hinge in place? Is it just a little spring-loaded bar 
> > similar
> > to the thing that usually holds watch straps on? Is it easy to fix? I don't
> > want to mess with it yet in case I break the other end too!!
> >
> > Any help appreciated.
> >
> > Dave Bellamy.
> 
> < This message was delivered via the Olympus Mailing List >
> < For questions, mailto:owner-olympus@xxxxxxxxxxxxxxx >
> < Web Page: http://Zuiko.sls.bc.ca/swright/olympuslist.html >

< This message was delivered via the Olympus Mailing List >
< For questions, mailto:owner-olympus@xxxxxxxxxxxxxxx >
< Web Page: http://Zuiko.sls.bc.ca/swright/olympuslist.html >


<Prev in Thread] Current Thread [Next in Thread>
Sponsored by Tako
Impressum | Datenschutz