Velcro also comes in double-sided variety (one side hooks, the other loops)
and can stick to itself in a loop or circle....sometimes sold in sporting
goods stores in the fishing department and referred to as "rod-wraps" (used
to bind fishing rods together for travel).
Bruce Kolber
St. Petersburg, FL 33715
USA
----- Original Message -----
From: "Mickey Trageser" <mickeytr@xxxxxxxxxxxxxxx>
To: <olympus@xxxxxxxxxxxxxxx>
Sent: Sunday, May 13, 2001 12:20 AM
Subject: Re: [OM] Need T-32 part. (WAS: Problem with T-32)
> I'd thought of electrical tape or cable ties, but they have to cross over
> the battery cover. I think I'll experiment with some velcro. It's
available
> in either an adhesive-backed type or non adhesive. If bought in
non-adhesive
> strips, I can take a short loop strip and and a long hook strip to form a
> self-adjusting strap to encircle the case and bind it together between
> battery changes. That way no stickey goo on the case from tape, no further
> damage to the case from glue, and no inconvenient obstruction of the
battery
> cover by tape or straps.
>
> If I'm a little thoughtful about it, the strap could also aid in the
> mounting of the 'flash in the pan' flash diffuser attachment. (Had to find
> that 'silver lining' in the quest. ...or is it aluminum?)
>
> Mickey
> ----- Original Message -----
> From: "gwsears" <gwsears@xxxxxxxxxxxxxxx>
> To: <olympus@xxxxxxxxxxxxxxx>
> Sent: Saturday, May 12, 2001 9:29 PM
> Subject: Re: [OM] Need T-32 part. (WAS: Problem with T-32)
>
>
> >
> > Electrical tape may do as well.
> >
> > GeoW
> >
> > On 12 May 2001, at 19:20, Mickey Trageser wrote:
> >
> > > Anyone have a recommendation as to a good glue for this purpose?
> > >
> > > TIA- Mickey
> > > ----- Original Message -----
> > > From: ClassicVW@xxxxxxx
> > > To: olympus@xxxxxxxxxxxxxxx
> > > Sent: Saturday, May 12, 2001 5:01 PM
> > > Subject: Re: [OM] Need T-32 part. (WAS: Problem with T-32)
> > >
> > >
> > > I think not. I can recall this question being asked a couple of
> > > years ago (because at the time I was also taking apart a T-32 to
> > > replace a broken foot) and the answer was to just glue it together,
> > > but choose only a few locations for the glue, and remember where the
> > > glue spots are in case you need to take it apart again.
> > >
> > > George S.
> > >
> > > mickeytr@xxxxxxxxxxxxxxx writes:
> > >
> > >
> > > I was able to tuck it all back together, but the tabs on the top
> > > shell are broken. Can a top shell for the T-32 be purchased?
> > >
> > >
> > >
> > >
> > >
> > >
> >
> >
> >
> > < This message was delivered via the Olympus Mailing List >
> > < For questions, mailto:owner-olympus@xxxxxxxxxxxxxxx >
> > < Web Page: http://Zuiko.sls.bc.ca/swright/olympuslist.html >
> >
>
>
> < This message was delivered via the Olympus Mailing List >
> < For questions, mailto:owner-olympus@xxxxxxxxxxxxxxx >
> < Web Page: http://Zuiko.sls.bc.ca/swright/olympuslist.html >
>
< This message was delivered via the Olympus Mailing List >
< For questions, mailto:owner-olympus@xxxxxxxxxxxxxxx >
< Web Page: http://Zuiko.sls.bc.ca/swright/olympuslist.html >
|